Firstly you need a network crossover cable. Available from most computer stores. This is a special type of cable (not a standard LAN cable)
Secondly Make sure both computers are on the same workgroup. TO do this Right click on My computer, Properties, go to the Computer Name Tab, See what is written in Workgroup. Change one computer by clicking on change and then type in the name of the other computer in the workgroup space down the bottom. Do not make the computer part of a domain. You want Workgroup.
This name change will require a computer reboot.
When both computers are on the same workgroup, we need to set IP Addresses.
In Control Panel, Open Network Settings.
Right click on Local Area Connections and select properties.
Under the heading "This connection uses the following items, Find Internet Protocol (TCP/IP)
Highlight it, Make sure you don't untick the box, and click on properties
Under the heading Use the following IP Address ENter in the Following on ONE Computer.
IP Address 192.168.0.10
Subnet Mask 255.255.255.0
Default Gateway LEave Blank
Under the Heading Obtain DNS Serveraddress automatically
Set this to Automatic. Don't enter anything in.
On the second computer Make the IP Address 192.168.0.20
Everything else the same.
This should be all.
1 step: - you have a cable his name is
TIA/EIA 568-B.2 CATEGORY 5e
And RJ45 connector
2step: - make a cross cable
1st point 2nd point of cable wires
1--------3
2--------6
3--------1
4--------4
5--------5
6--------2
7--------7
8--------8
Cable each wires setting.
3 steps: your computer have install Ethernet hardware
How to
Right click "my computer"
Move mouse "computer properties"
Click "hardware" tab menu
Click "Device Manager"
Device manager window is open
Check network adapter
"PCI Fast Ethernet NIC" is work or not?
If NIC device is work then do next work
Else Nick device have cross simple then double click NIC device.
And "Enable Device"
Device usage: use this device (enable)
End work
next
4 steps. Create a ip address to both system are not same (My network places)
Click: - "view network connections" in network tasks
Right click: - local area connection
Ex: Realtek RTL8139 family PCI
Click: properties
Click 'this connection uses the following item:'
Internet protocol (TCP/IP) click "properties"
Use the following IP address
Ex: -
1st PC 192.168.0.100
Subnet mask 255.255.255.0
2nd Pc 192.168.0.200
Subnet mask 255.255.255.0
Click "ok" "ok"
4 steps: dos command check connection
Ping ip address (other pc)
Ex: ping 192.168.0.100
They have checking connection
And massage report
5.click in network task Firwall setting change
Off (not recommended) both system.
6-check group are same in my computer properties "computer Name"
Ex: "workgroup"
7. Then plug in cable to computer pc1 pc2.
Then massage is display "network cable is plugging with 100mbps"
Then click "network placese" and click "view workgroup computer"
 |
| A RJ45 Crossover cable |
Secondly Make sure both computers are on the same workgroup. TO do this Right click on My computer, Properties, go to the Computer Name Tab, See what is written in Workgroup. Change one computer by clicking on change and then type in the name of the other computer in the workgroup space down the bottom. Do not make the computer part of a domain. You want Workgroup.
This name change will require a computer reboot.
When both computers are on the same workgroup, we need to set IP Addresses.
In Control Panel, Open Network Settings.
Right click on Local Area Connections and select properties.
Under the heading "This connection uses the following items, Find Internet Protocol (TCP/IP)
Highlight it, Make sure you don't untick the box, and click on properties
Under the heading Use the following IP Address ENter in the Following on ONE Computer.
IP Address 192.168.0.10
Subnet Mask 255.255.255.0
Default Gateway LEave Blank
Under the Heading Obtain DNS Serveraddress automatically
Set this to Automatic. Don't enter anything in.
On the second computer Make the IP Address 192.168.0.20
Everything else the same.
This should be all.
1 step: - you have a cable his name is
TIA/EIA 568-B.2 CATEGORY 5e
And RJ45 connector
2step: - make a cross cable
1st point 2nd point of cable wires
1--------3
2--------6
3--------1
4--------4
5--------5
6--------2
7--------7
8--------8
Cable each wires setting.
3 steps: your computer have install Ethernet hardware
How to
Right click "my computer"
Move mouse "computer properties"
Click "hardware" tab menu
Click "Device Manager"
Device manager window is open
Check network adapter
"PCI Fast Ethernet NIC" is work or not?
If NIC device is work then do next work
Else Nick device have cross simple then double click NIC device.
And "Enable Device"
Device usage: use this device (enable)
End work
next
4 steps. Create a ip address to both system are not same (My network places)
Click: - "view network connections" in network tasks
Right click: - local area connection
Ex: Realtek RTL8139 family PCI
Click: properties
Click 'this connection uses the following item:'
Internet protocol (TCP/IP) click "properties"
Use the following IP address
Ex: -
1st PC 192.168.0.100
Subnet mask 255.255.255.0
2nd Pc 192.168.0.200
Subnet mask 255.255.255.0
Click "ok" "ok"
4 steps: dos command check connection
Ping ip address (other pc)
Ex: ping 192.168.0.100
They have checking connection
And massage report
5.click in network task Firwall setting change
Off (not recommended) both system.
6-check group are same in my computer properties "computer Name"
Ex: "workgroup"
7. Then plug in cable to computer pc1 pc2.
Then massage is display "network cable is plugging with 100mbps"
Then click "network placese" and click "view workgroup computer"
